• ********* SERVICE MANUAL **********. • CONTENTS Top cover & face plate attaching and removing.1 Base & bed cover attaching and removing.. When a stranger calls 720p download. 2 Belt cover attaching and removing..3 Front panel attaching and removing.. 4 To adjust the presser bar height..5 To adjust the needle drop.. • Top cover & face plate attaching and removing TOP COVER (Y) (TO REMOVE) 1. Remove 3 screws (A & B) and top cover.
(TO ATTACH) 2. Attached the top cover with 3 screws (A and B). FACEPLATE (Z) (TO REMOVE) 3.
• Base & bed cover attaching and removing BASE (Y) (TO REMOVE) 1. Remove 6 screws (A) and base.
(TO ATTACH) 2. Attach the base with 6 screws (A). BED COVER (Z) (TO REMOVE) 3. Move the drop lever to the left, then remove 2 screws (B). • Belt cover attaching and removing (TO REMOVE) 1.
Janome Memory Craft 6000 Sewing Machine PDF Instruction Manual in English. This electronic copy contains everything you need to know about your Janome Memory Craft 6000 Sewing Machine, including detailed information on how to thread and operate the machine. Your copy will be emailed within 24 hours of your payment clearing – normally quicker! Janome Memory Craft 3000 Service Manual. Also See for Memory Craft 3000. Quick manual - 2 pages Instruction book - 42 pages. Table of Contents. Also See for Janome Memory Craft 3000. Janome memory craft 3000 Instruction Book 42 pages. Janome Memory Craft 3000 Quick Manual 2 pages.
Remove 2 screws (A) and belt cover (Y), then pull out. (TO ATTACH) 2. Attach the belt cover (Y) with 2 screws (A). • Front panel attaching and removing (TO REMOVE) 1. Remove the top cover, belt cover and bed cover (See pages 1, 2 and 3). Remove screw A and loose screws (B, C, D, E, F and G).
Pull out connectors (H) and remove the front panel. (TO ATTACH) 4. • To adjust the presser bar height The standard presser bar height is 6.0 mm between the bottom surface of the foot (A) and needle plate(B) when the presser bar (C) lifter is lifted. Open the face plate. Raise the presser foot, loosen the presser bar bracket screw (D) and adjust the height to 6.0 mm.
• To adjust the needle drop When you select the pattern 01 (straight stitch on center needle position), the needle drop should be in the center position of the needle hole in the needle plate. When the needle swings in maximum zigzag width, the distance between both edges of the needle hole on the needle plate and the needle drop position should be equal as shown below (*** C ***). • To adjust the needle bar height The standard distance between the upper edge of the needle eye (A) and the tip of shook should be in the range of 1.6 to 2.0 mm when the tip of hook meets the right side of the needle (B) in ascending travel of needle from its left and lowest position.
- Author: admin
- Category: Category
• ********* SERVICE MANUAL **********. • CONTENTS Top cover & face plate attaching and removing.1 Base & bed cover attaching and removing.. When a stranger calls 720p download. 2 Belt cover attaching and removing..3 Front panel attaching and removing.. 4 To adjust the presser bar height..5 To adjust the needle drop.. • Top cover & face plate attaching and removing TOP COVER (Y) (TO REMOVE) 1. Remove 3 screws (A & B) and top cover.
(TO ATTACH) 2. Attached the top cover with 3 screws (A and B). FACEPLATE (Z) (TO REMOVE) 3.
• Base & bed cover attaching and removing BASE (Y) (TO REMOVE) 1. Remove 6 screws (A) and base.
(TO ATTACH) 2. Attach the base with 6 screws (A). BED COVER (Z) (TO REMOVE) 3. Move the drop lever to the left, then remove 2 screws (B). • Belt cover attaching and removing (TO REMOVE) 1.
Janome Memory Craft 6000 Sewing Machine PDF Instruction Manual in English. This electronic copy contains everything you need to know about your Janome Memory Craft 6000 Sewing Machine, including detailed information on how to thread and operate the machine. Your copy will be emailed within 24 hours of your payment clearing – normally quicker! Janome Memory Craft 3000 Service Manual. Also See for Memory Craft 3000. Quick manual - 2 pages Instruction book - 42 pages. Table of Contents. Also See for Janome Memory Craft 3000. Janome memory craft 3000 Instruction Book 42 pages. Janome Memory Craft 3000 Quick Manual 2 pages.
Remove 2 screws (A) and belt cover (Y), then pull out. (TO ATTACH) 2. Attach the belt cover (Y) with 2 screws (A). • Front panel attaching and removing (TO REMOVE) 1. Remove the top cover, belt cover and bed cover (See pages 1, 2 and 3). Remove screw A and loose screws (B, C, D, E, F and G).
Pull out connectors (H) and remove the front panel. (TO ATTACH) 4. • To adjust the presser bar height The standard presser bar height is 6.0 mm between the bottom surface of the foot (A) and needle plate(B) when the presser bar (C) lifter is lifted. Open the face plate. Raise the presser foot, loosen the presser bar bracket screw (D) and adjust the height to 6.0 mm.
• To adjust the needle drop When you select the pattern 01 (straight stitch on center needle position), the needle drop should be in the center position of the needle hole in the needle plate. When the needle swings in maximum zigzag width, the distance between both edges of the needle hole on the needle plate and the needle drop position should be equal as shown below (*** C ***). • To adjust the needle bar height The standard distance between the upper edge of the needle eye (A) and the tip of shook should be in the range of 1.6 to 2.0 mm when the tip of hook meets the right side of the needle (B) in ascending travel of needle from its left and lowest position.